Adjustable Half Eternity Diamond Bolo Bracelet in 14K White Gold

What Is a Diamond Bolo Bracelet?

A diamond bolo bracelet closes with a sliding bead instead of a clasp, so it pulls to any wrist size. This one is solid 14K white gold, set with 27 round lab grown diamonds across half the circumference, on a setting rail 2.4 mm wide by 2.6 mm high. Total weight options are 1, 1 1/2, 2, and 3 ct.

Product type

Adjustable half eternity diamond bolo bracelet

Metal

Solid 14K white gold as shown

Stones

27 round brilliant lab grown diamonds

Total carat weight

1 ct, 1 1/2 ct, 2 ct, or 3 ct

Setting

Four prong links covering half the circumference

Setting dimensions

2.4 mm wide by 2.6 mm high in the configuration shown

Closure

Bolo slider on a woven chain, no clasp, adjusts to fit

Customization

Gold karat, gold color, total carat weight, and stone type

It is aimed at the buyer who likes the look of a diamond line on the wrist but does not want to size a bracelet, fasten a box clasp one handed, or worry about losing it off the wrist during the day. Among our tennis bracelets, this is the version that fits without being measured.

How Does the Bolo Slider Adjust to the Wrist?

Both ends of the woven chain pass through a single polished slider and finish in small ball tips. Pulling the two tips draws the bracelet closed, and pushing the slider back opens it. The slider grips by friction rather than by a catch, so there is nothing to unclip, nothing to line up, and the whole action can be done with one hand against the edge of a table. The ball tips stop the chain from pulling free at full extension.

Only half the circumference carries diamonds, which is what makes the adjustment work. The stone section is a rigid strip of prong set links measuring 2.4 mm wide by 2.6 mm high, while the remaining half is plain woven chain that can travel through the slider. Because the diamond strip is the heaviest part of the bracelet, it settles across the top of the wrist on its own weight, whatever length the slider is set to. On the wrist the visible result is a straight diamond line with the chain disappearing behind it.

Which Metal and Diamonds Go Into This Bracelet?

Chain, links, and slider are solid 14K gold, cast and finished on site by our own production team, with white as shown and yellow or rose available in the same construction. The 27 round brilliants come from our lab grown diamonds inventory and are covered by a diamond test certificate, with total weight built to 1, 1 1/2, 2, or 3 ct.

• ◆ Each diamond sits in its own four prong link, and the links are joined by U shaped bridges so the strip bends with the wrist rather than standing away from it
• ◆ The 27 stones are matched as a single run before any of them are set, because a graduated line shows every mismatch in color or diameter along its length
• ◆ The slider is fitted to a calibrated friction, tight enough to hold position through a working day and loose enough to move under finger pressure, then tested on the finished chain
• ◆ Every finished piece is checked at the bench for stone security, prong height, slider tension, and chain wear before it leaves production

Which Options Can Be Chosen Before Production?

This bolo bracelet is built to order. The configuration shown is a starting point, not a fixed SKU. The following options can be specified before production starts.

• ◆ Total diamond weight: 1, 1 1/2, 2, or 3 ct
• ◆ Gold karat: 14K as shown, or 18K for a warmer, denser color
• ◆ Gold color: white as shown, with yellow and rose in the same construction
• ◆ Diamond coverage: half the circumference as shown, or extended further around the chain
• ◆ Stone type: lab grown diamond as standard, with natural diamond available on request

For fully custom designs beyond these options, start here →